SKR 1.3 – VS Code with PlatformIO install
This is a brief tutorial on how to install VSCode with PlatformIO for Marlin firmware compiles and uploads on the SKR 1.3 printer motherboard.
One Time Tips, You Can PayPal Me:
Hardware:
1 – BigTreeTech SKR 1.3
1 – USB Serial cable
Documentation:
Amazon Affiliate Links:
(SKR v1.3)
(Acer Nitro 5 Laptop)
Software:
Marlin Firmware 2.0.x
VScode:
Pronterface:
Nguồn: https://ftlinuxcourse.com
Xem thêm bài viết khác: https://ftlinuxcourse.com/huong-dan-cai-dat
Xem thêm Bài Viết:
- Trải nghiệm mới hay ho với hướng dẫn cài Mac Os trên vmware
- Bật mí cách cài đặt ssl miễn phí lên Let’s Encrypt
- Tuyệt chiêu tạo usb boot kali linux đơn giản dành cho bạn
- Hướng dẫn chi tiết từ A – Z các bước cài đặt Python trên Windows 10
- Bật mí quy trình cài đặt Kali Linux trên Vmware đúng chuẩn và chi tiết
Comments
Don Szenina
AuthorThanks for doing this tutorial… It was a big help with getting my Tevo Tornado running with the SKR 1.3 motherboard.
joe fuzz
AuthorI fave a bin file for my printer that I need to modify. How can I get this into VS Code so I can make changes?
joe fuzz
Authoris there a way to take an existing .bin file and uncompile it so I can see the file in vs code?
Work Peaceful
Authorsame Arduino IDE ? no upload via TF Card
Patrick Bodine
AuthorAfter having multiple computer issues, I finally found a computer that would compile my build, before it could be sent to the printer, the power went out. Now, platformio just continually wants to install.
GuiHome-Maker
AuthorHi, the subtitles are very good but there are a few mistakes. If you want I can remove the errors of conjugations contained in the sentences?
Michael Allbright
AuthorI bought an SKR v1.3 after watching your video and was amazed to find 2-3V of ripple! on the 5V switching power supply even though the 24V input had only 120mV of ripple going in. They do seem to have put some thought into the filter network on the 3.3V supply (not that it helps much with right around 1V of ripple), but there's no such network on the 5V supply. Just curious if this is typical, or if my board is just defective–have you tried putting an oscilloscope on yours?
Muzz Litebeer
Author@9:40… why did you do this?
When I got to the end of the video and sent the M119 command, the endstops all reported 'open'. Is that a problem? Should I change it back?
devians88
AuthorThanks!
Very help full video!
Innov8 Gr8 D-zynz
AuthorThank you for this, cheers.
T-COX
AuthorHello,
thanks for your video.
Can you tel me how can i config marlin to laser mode?
joe fuzz
AuthorSo I have been able to connect to my printer. In manual mode I can jog x, y and z.
When I send m119 I get endstop “triggered “whether they are or not.
The level sensor light is not on.
Calling for bed heat, or, nozzle heat, I get nothing.
For example when I send m140 s60 I get “unknown command”. I think the output of the SKR HE0 connections should be 24vdc (firing the SSR to heat the bed). Am I correct in this?
This leads me to think that the firmware isn’t set up right.
I started with “Marlin-bugfix-2.0.x”
In configuration.h, I changed:
1. #define SERIAL_PORT -1
2. #define BAUDRATE 115200
3. #define MOTHERBOARD BOARD_BIGTREE_SKR_V1_3
In platform.ini, I changed:
1. default_envs = LPC1768
I compiled using visual studio code
Any thoughts?
Thanks, Joe
Linda Fazekas
AuthorSo I have been able to connect to my printer. In manual mode I can jog x, y and z.
When I send m119 I get endstop “triggered “whether they are or not.
The level sensor light is not on.
Calling for bed heat, or, nozzle heat, I get nothing.
For example when I send m140 s60 I get “unknown command”. I think the output of the SKR HE0 connections should be 24vdc (firing the SSR to heat the bed). Am I correct in this?
This leads me to think that the firmware isn’t set up right.
I started with “Marlin-bugfix-2.0.x”
In configuration.h, I changed:
1. #define SERIAL_PORT -1
2. #define BAUDRATE 115200
3. #define MOTHERBOARD BOARD_BIGTREE_SKR_V1_3
In platform.ini, I changed:
1. default_envs = LPC1768
I compiled using visual studio code
Any thoughts?
Thanks, Joe
Aleksandr F
AuthorGreat job! Thanks! Отличная работа! Спасибо!
N0mNus
Authorthanks for video… and german sub 😀
ksaizo
AuthorThank you Edward for this tutorial! It really helped me a lot! To be recognized the motherboard from the computer, we must check if the red jumper is shortsircuit +5v and USB. Otherwise will not activate the MB and the computer will not see it!
AwkwardDinosaur
AuthorI'd like to start of by saying that you're videos are enormously helpful and informative, but I do have a suggestion related to the production of your videos. A number of your recent uploads feature thumbnails with rather hard to read text, I would recommend using (if you are able) a contrasting white/black outline to help it stand out a little more against the background.
Dies Martis
AuthorYou're my favorite teacher, Edward. Thanks!
Hagiu Valentin
AuthorI love your videos and the way how you explain.
Ömer Talha Başoğlu
AuthorNice tutorials man, I'm following especially SKR 1.3 videos because of building my own 3D printer thanks to you.
dadog92
AuthorGreat video!
The Best Stooge
AuthorI stopped using Atom very shortly after I started with Atom and I never looked back.